DIY Philips R 900 rack

[ducks007]

Hello

I've find a R900 rack for the 900 serie but unfortunaly too far from my home.
So it give me an idee to make a "copy" of this rack and because I work on drawing office it will be nor very hard to do it.
I just should have your help (people who have the real R 900) to give me some dimensions :
for that, I've made a 3D drawing with letters for dimensions and if you can complete my list it will help me very much

let's go

[ducks007]

[ducks007]

[ducks007]

if the picts are too little, you can give me a mail to have the full size pictures

If you have picts of the real R900 it will help me too

[mthecatlover]

[ducks007]

that's this one, thanks for this Philips publicity

[Albert900]

I have such a rack

will try to do some measurements later this week.

[Albert900]

Hi, I have most of the dimensions here. The rest I will try to add Tuesday or Wednesday.
Accuracy is +/- 1mm

Etageres (4x)
A: 450 mm
B: 540 mm
C: 426 mm
D: 565 mm
E: 7 mm

Plateau superieur
F: 490 mm
G: 655 mm
H: 466 mm
I: 680mm
J: 7 mm

Base
K: 20 mm
L: 465 mm
M: 465 mm

Sup
N: 240 mm (approximately, as it is mounted it is hard to measure)
O: 125 mm
P: 340 mm
Q: 485 mm
R: 125 mm
The sides O/P/R are 20 mm (identical to K), side Q is 5 mm thick

Montant droite + gauche
S: 125 mm
T: 1000 mm

For U/V/W/X I measured the distance from floor to glass plate etc.

Floor-bottom 1st glass plate: 363 mm
Top 1st glass plate: 370 mm

Floor-bottom 2nd glass plate: 512 mm
Top 2nd glass plate: 519 mm

Floor-bottom 3rd glass plate: 681 mm
Top 3rd glass plate 688 mm

Floor-bottom 4th glass plate: 870 mm
Top 4th glass plate 877 mm

The cut-outs for the glass plates are 72 mm horizontal (both sides) and 12 mm high. There are rubber inserts to place the glass plates on, thickness .... (I will measure)

Montant AR
Y: I didn't measure Y, but the cut-out lengte on the sides, which is 28 mm
Z: 40 mm
ZZ: not on your drawing, but the cable cut-outs (Y-Z) are each 20 mm above the cut-out for the glass plates.
AA: 125 mm
BB: 1.75mm

[ducks007]

Waouuu !
A BIG thank you !
now I can adjust my 3d Drawing will all your informations

[ducks007]

I've a little question about the right and left corner profile, what is the thickness of those profiles?
and you say O/P/R are 20mm and Q 5mm : is that a bend of 20mm and 5 mm of a plate with a different thickness or is this plate was 5mm thickness with 20mm bends hight ?

[Albert900]

I added N and BB to the table.
Thickness of the metal used, columns as well as base and sup, is 1.75 mm.

Plate sup is thus also made of 1.75 mm thick metal, with bends of 20 mm (same for base). Except for Q, here only bend down for 5 mm, so there is some more space for a 900-series unit. As you can see on my picture the DSC950 just fits underneath sup, if Q was also 20 mm it wouldn't.

To measure Y and Z I have to take equipment out, will try to do this later this week.

[ducks007]

Many thanks Albert, with all your informations, i've rearanged my 3D model

work in progress :

[Albert900]

I added dimensions for the Y-Z cable cut-outs. These are not centered between the glass plates, but all are at 20 mm above the cut-out for the glass plates.

Which format is your 3D design in?

[ducks007]

Many thanks Albert.
I work with Solidworks (that's the software I used at my job)

[mthecatlover]

Sorry for the topic hijack, ... I think I will change this in a FB820/FB830 rack. The height is adjustable. Measurements are easy to adjust... The shelfs can be made from either glass or composite. Black hard material for kitchen workblades. Very sturdy and strong.