Pagina 1 van 3

DIY Philips R 900 rack

Geplaatst: vr feb 09, 2018 2:31 pm
door ducks007
Hello :wink:

I've find a R900 rack for the 900 serie but unfortunaly too far from my home.
So it give me an idee to make a "copy" of this rack and because I work on drawing office it will be nor very hard to do it.
I just should have your help (people who have the real R 900) to give me some dimensions :
for that, I've made a 3D drawing with letters for dimensions and if you can complete my list it will help me very much :pray: :clap:

let's go :dance:
r900 (Large).jpg
tablette sup (Large).jpg
etagere (Large).jpg

Re: DIY Philips R 900 rack

Geplaatst: vr feb 09, 2018 2:34 pm
door ducks007
base (Large).jpg
plateau sup (Large).jpg
montant (Large).jpg

Re: DIY Philips R 900 rack

Geplaatst: vr feb 09, 2018 2:35 pm
door ducks007
montant ar (Large).jpg
dimensions (Large).jpg

Re: DIY Philips R 900 rack

Geplaatst: vr feb 09, 2018 2:37 pm
door ducks007
if the picts are too little, you can give me a mail to have the full size pictures :wink:

If you have picts of the real R900 it will help me too :wink:

Re: DIY Philips R 900 rack

Geplaatst: za feb 10, 2018 11:16 pm
door mthecatlover
Afbeelding

Re: DIY Philips R 900 rack

Geplaatst: ma feb 12, 2018 9:29 am
door ducks007
that's this one, thanks for this Philips publicity :clap:

Re: DIY Philips R 900 rack

Geplaatst: ma feb 12, 2018 11:50 am
door Albert900
I have such a rack
Afbeelding
will try to do some measurements later this week.

Re: DIY Philips R 900 rack

Geplaatst: ma feb 12, 2018 11:51 pm
door Albert900
Hi, I have most of the dimensions here. The rest I will try to add Tuesday or Wednesday.
Accuracy is +/- 1mm

Etageres (4x)
A: 450 mm
B: 540 mm
C: 426 mm
D: 565 mm
E: 7 mm

Plateau superieur
F: 490 mm
G: 655 mm
H: 466 mm
I: 680mm
J: 7 mm

Base
K: 20 mm
L: 465 mm
M: 465 mm

Sup
N: 240 mm (approximately, as it is mounted it is hard to measure)
O: 125 mm
P: 340 mm
Q: 485 mm
R: 125 mm
The sides O/P/R are 20 mm (identical to K), side Q is 5 mm thick

Montant droite + gauche
S: 125 mm
T: 1000 mm

For U/V/W/X I measured the distance from floor to glass plate etc.

Floor-bottom 1st glass plate: 363 mm
Top 1st glass plate: 370 mm

Floor-bottom 2nd glass plate: 512 mm
Top 2nd glass plate: 519 mm

Floor-bottom 3rd glass plate: 681 mm
Top 3rd glass plate 688 mm

Floor-bottom 4th glass plate: 870 mm
Top 4th glass plate 877 mm

The cut-outs for the glass plates are 72 mm horizontal (both sides) and 12 mm high. There are rubber inserts to place the glass plates on, thickness .... (I will measure)

Montant AR
Y: I didn't measure Y, but the cut-out lengte on the sides, which is 28 mm
Z: 40 mm
ZZ: not on your drawing, but the cable cut-outs (Y-Z) are each 20 mm above the cut-out for the glass plates.
AA: 125 mm
BB: 1.75mm

Re: DIY Philips R 900 rack

Geplaatst: di feb 13, 2018 9:20 am
door ducks007
Waouuu !
A BIG thank you ! :clap:
now I can adjust my 3d Drawing will all your informations :dance:

Re: DIY Philips R 900 rack

Geplaatst: di feb 13, 2018 12:05 pm
door ducks007
I've a little question about the right and left corner profile, what is the thickness of those profiles?
and you say O/P/R are 20mm and Q 5mm : is that a bend of 20mm and 5 mm of a plate with a different thickness or is this plate was 5mm thickness with 20mm bends hight ?

Re: DIY Philips R 900 rack

Geplaatst: wo feb 14, 2018 12:34 am
door Albert900
I added N and BB to the table.
Thickness of the metal used, columns as well as base and sup, is 1.75 mm.

Plate sup is thus also made of 1.75 mm thick metal, with bends of 20 mm (same for base). Except for Q, here only bend down for 5 mm, so there is some more space for a 900-series unit. As you can see on my picture the DSC950 just fits underneath sup, if Q was also 20 mm it wouldn't.

To measure Y and Z I have to take equipment out, will try to do this later this week.

Re: DIY Philips R 900 rack

Geplaatst: wo feb 14, 2018 2:38 pm
door ducks007
Many thanks Albert, with all your informations, i've rearanged my 3D model :clap:

work in progress :
r900 (Large).JPG
r900-2 (Large).JPG

Re: DIY Philips R 900 rack

Geplaatst: vr feb 16, 2018 7:15 pm
door Albert900
I added dimensions for the Y-Z cable cut-outs. These are not centered between the glass plates, but all are at 20 mm above the cut-out for the glass plates.

Which format is your 3D design in?

Re: DIY Philips R 900 rack

Geplaatst: za feb 17, 2018 11:13 am
door ducks007
Many thanks Albert.
I work with Solidworks (that's the software I used at my job) 8)

Re: DIY Philips R 900 rack

Geplaatst: ma feb 19, 2018 10:56 pm
door mthecatlover
Sorry for the topic hijack, :idea:... I think I will change this in a FB820/FB830 rack. The height is adjustable. Measurements are easy to adjust... :idea: The shelfs can be made from either glass or composite. Black hard material for kitchen workblades. Very sturdy and strong.